“爬行”是全自動攪拌車液壓傳動中經常出現的不正常運動狀態。輕微的“爬行”使運動件產生目光不易覺察的振動，顯著的“爬行”使運動件產生大距離地跳動。爬行現象是很有害的，因此“爬行”現象對于改善液壓系統穩定性和提高機床加工精度是非常重要的。
"Crawling" is an abnormal movement state that often occurs in the hydraulic transmission of full-automatic mixer. Slight "crawling" causes the moving parts to vibrate imperceptibly, while significant "crawling" causes the moving parts to jump at a large distance. Creeping phenomenon is very harmful, so eliminating "creeping" phenomenon is very important to improve the stability of hydraulic system and improve the machining accuracy of machine tools.
驅動剛性差引起的“爬行”
"Creeping" caused by poor driving rigidity
空氣進入油液中后，一部分溶于壓力油液中，其余部分就形成氣泡浮游在壓力油中。因為空氣有壓縮性，使液壓油產生明顯的彈性，造成驅動剛性差而引起“爬行”。
After the air enters the oil, part of it will dissolve in the pressure oil, and the rest will form bubbles to float in the pressure oil. Because the air has compressibility, the hydraulic oil has obvious elasticity, resulting in poor driving rigidity and "crawling".
在制造和修配零件時，應嚴格達到公差要求，裝配時要保證配合間隙。緊固各管道連接處，防止泄漏。均勻緊固各接合面處的連接螺釘，密封墊應均勻，不允許用多層紙墊。附著于濾油器上的臟物，應采用容量足夠的濾油器。改進液壓系統，設法防止系統中出現局部真空，并設置必要的排氣塞或放氣閥。
When manufacturing and repairing parts, the tolerance requirements shall be strictly met, and the fit clearance shall be ensured during assembly. Tighten the connections of all pipelines to prevent leakage. Tighten the connecting screws at all joint surfaces evenly, and the sealing gasket shall be uniform. Multi layer paper pads are not allowed. The oil filter with sufficient capacity shall be used to remove the dirt attached to the oil filter. Improve the hydraulic system, try to prevent local vacuum in the system, and set necessary vent plug or vent valve.
液壓元件間隙大引起的“爬行”
"Creeping" caused by large clearance of hydraulic components
運動件低速運動時，一旦發生干摩擦，阻力增加。這時要求液壓泵提高壓力，但由于液壓泵間隙大而嚴重漏油，不能適應執行元件因阻力的變化而形成的壓力變化而產生“爬行”。
When the moving part moves at low speed, once dry friction occurs, the resistance increases. At this time, the hydraulic pump is required to increase the pressure, but due to the large clearance of the hydraulic pump and serious oil leakage, it can not adapt to the pressure change of the actuator due to the change of resistance, resulting in "crawling".
修復或更換液壓泵內零件，保證裝配要求的間隙，以減少液壓泵的泄漏。
Repair or replace the parts in the hydraulic pump to ensure the clearance required for assembly, so as to reduce the leakage of the hydraulic pump.
控制閥失靈引起的“爬行”：各種控制閥的阻尼孔及節流口被污物堵塞，閥芯移動不靈活等，使壓力波動大，造成推力或流量時大時小而產生“爬行”。
"Crawling" caused by control valve failure: the damping holes and throttles of various control valves are blocked by dirt, and the valve core is not flexible to move, which makes the pressure fluctuate greatly, resulting in "crawling" due to large thrust or small flow.
保持油液清潔，定期清洗并更換，加強元件的維護，以防液壓油污染。
Keep the oil clean, clean and replace regularly, and strengthen the maintenance of components to prevent hydraulic oil pollution.
摩擦阻力變化引起的“爬行”
"Creep" caused by friction resistance change
全自動攪拌車廠家認為這種現象在液壓缸出現的較多，主要由于液壓缸中心線與活塞桿不平行，活塞桿局部或全長彎曲，缸筒內圓被拉毛刮傷，缸筒精度達不到技術要求，活塞桿兩端油封調整過緊等因素會(huì )引起“爬行”。
The manufacturers of full-automatic mixer truck believe that this phenomenon occurs more in the hydraulic cylinder, mainly because the center line of the hydraulic cylinder is not parallel to the piston rod, the piston rod is partially or fully bent, the inner circle of the cylinder barrel is roughened and scratched, the accuracy of the cylinder barrel cannot meet the technical requirements, and the oil seals at both ends of the piston rod are adjusted too tightly, which will cause "crawling".
逐項檢驗液壓缸的精度及損傷情況，并進行修復或更新。液壓缸安裝精度應符合技術要求。
Inspect the accuracy and damage of the hydraulic cylinder item by item, and repair or update it. The installation accuracy of hydraulic cylinder shall meet the technical requirements.
以上就是問題的相關介紹內容了，希望對您有所幫助，您可以關注我們網站m.zgclmw.com，了解咨詢更多詳細的信息，我們的客服人員也會(huì )為您提供好的服務！
The above is the relevant introduction to the problem. I hope it can help you. You can follow our website www.zkzdsljbc COM, for more detailed information, our professional customer service staff will also provide you with good service!
